Find Jobs
Hire Freelancers

PCB Modification of only one RJ14 connector

$10-30 CAD

Completed
Posted almost 4 years ago

$10-30 CAD

Paid on delivery
We have a small PCB that contains 2 RJ45 jack one per short side, and 1 RJ14. An error on the RJ14 must be corrected. This Jack on the long side of the board must now accommodate an 6 PIN 4 CONTACT jack. The only modification needed are to move the two drill holes where the plastic jack pushes into the PCB (Wider than on the current design). All files are provided. Our engineer is on leave and we need to produce the new boards as an interface.
Project ID: 25755520

About the project

12 proposals
Remote project
Active 4 yrs ago

Looking to make some money?

Benefits of bidding on Freelancer

Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
Awarded to:
User Avatar
hello sir. I have just read your job description and your project is really interesting to me. The Items you raised are similar to what I have already done in practice and I think you can do it in a short time if you have a little explanation. I'm an expert having specialization in Electronic Engineering Design. ✔️ Embedded system based on Microcontroller (ATMEGA, AVR, STM8, STM32, MSP430, TMS320, PIC ...) ✔️ A system based on development boards(Arduino, Raspberry PI, Node MCU, Bluechip, Teensy,…) ✔️ Antenna design & Analog circuit/RF communication circuit designing and simulation using Proteus, P-Spice, Tina Pro, ADS, CST, Ansys, HFSS ✔️ Bluetooth, WIFI, zigbee, LoRA ✔️ High-Speed layout using HyperLynx ✔️ PCB layout designing, providing GERBER and BOMs, 3D files using Altium, EAGLE, Kicad, EasyEDA… ✔️ Programming firmware of Microcontroller & C++ ✔️ BMS I think my many design and practical experiences can help you design your project and give you enough satisfaction. I look forward to your response.
$20 CAD in 7 days
5.0 (2 reviews)
1.3
1.3
12 freelancers are bidding on average $23 CAD for this job
User Avatar
Hi, Thank you for posting the project. I have looked over your information and it appears your PCB design was done in Altium Designer. I have extensive experience using Altium Designer to create schematics and board layouts and it would be very easy to update the design with your changes. I am also located in Canada which would make for very easy communication between us to get the final project requirements completed. I look forward to chatting with you with any questions you may have and to discuss this project further. You can read my reviews and look at many previous designs I have done in the past. Previous recent Freelancer work was to design a robot control system and 48V to 3.3 and 5.0 voltage power supply using Altium Designer. design an Arduino 2560 compatible system that could measure rotating spindle speed of a shaft and provide Bluetooth support Please contact me for further discussion My Name: Brad Bas Location: London, Ontario, Canada Work: 30 Years experience Embedded System Design completing electronic projects for Railway equipment and custom robotic machinery to test mechanical railway systems. Design and build from concept to prototype to production delivery
$30 CAD in 1 day
4.8 (4 reviews)
5.3
5.3
User Avatar
Hi. I can do this for you very fast. I saw the gerber files and indeed, this is a very simple PCB. Please let me know if you have access to the original files (the files used in the CAD environment, not the fabrication files). Also, if you have the files please let me know what tool do you use to design your PCB. I usually work with Altium and Allegro, but I can adapt to any other tool. Thanks.
$15 CAD in 1 day
5.0 (25 reviews)
4.9
4.9
User Avatar
Hello. I can complete this project perfectly. I have 10 years good experience of hardware development. I have completed a variety of embedded system design and programming by using microcontroller, arm, etc Board PCB design have been completed by using Altium and Protel99SE.
$30 CAD in 7 days
5.0 (4 reviews)
4.4
4.4
User Avatar
I do design in Eagle CAD, if your existing files are based in Eagle then its a very straightforward job.
$30 CAD in 1 day
5.0 (5 reviews)
4.4
4.4
User Avatar
I am an Electronics Design Engineer with More than 4 Years of Experience. I have design expertise in Embedded systems, Schematic design, PCB layout ,Hardware Debugging and hardware prototyping. I also have experience in designing Internet of Things,and Circuit design. I have done lots of projects based on PCB designing. Please put message so we can discuss in detail.
$15 CAD in 1 day
5.0 (7 reviews)
2.9
2.9
User Avatar
Dear Client, I had came across your post for building the PCB Layout design and I have the experience in PCB layout designing for more than 2 years up to 4 layers of design. Had completed many projects with ARM, PIC & ESP controllers and also in signal processing. Also I extend my support with programming as I am experienced with uKeil, Atmel Studio and MPLAB as well. I can do this projects in efficient way because I have an experience in building an IOT device with ESP32 for Temperature measurement, Humidity measurement, Heater Controller, Fan and Lighting Control etc. Deliverable: 1. Design Source File 2. Manufacturing GERBER files 3. 3D CAD of the PCB with all the components CAD assembled 4. Detailed BOM 5. Firmware Your project could be completed on time and submitted for your review. I will support you until your satisfaction. I am New to freelancing service but i had experience in working in an organisation, extremely interested to work on this project to showcase my skill. Looking forward to hear from you. Thanks, Kavin
$15 CAD in 5 days
5.0 (2 reviews)
0.6
0.6
User Avatar
Hi! My name is Stefan, and I have more of 12 years of experience in PCB design (Altium Designer, professional tool), and firmware in C. I could do it very quickly. Please feel free to contact me.
$15 CAD in 1 day
0.0 (0 reviews)
0.0
0.0
User Avatar
I'm already experienced with pcb design Relevant Skills and Experience Embedded hardware and software, iot, pcb design, web design and power electronics
$30 CAD in 3 days
0.0 (0 reviews)
0.0
0.0
User Avatar
Hi; I have been working as an avionics engineer for about 6 years. I took part in many PCB projects. I have 7 years of experience on the altium desigber. I worked with many different form factors and processor types.
$25 CAD in 1 day
0.0 (0 reviews)
0.0
0.0

About the client

Flag of CANADA
Montreal, Canada
5.0
3
Payment method verified
Member since Feb 4, 2016

Client Verification

Thanks! We’ve emailed you a link to claim your free credit.
Something went wrong while sending your email. Please try again.
Registered Users Total Jobs Posted
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Loading preview
Permission granted for Geolocation.
Your login session has expired and you have been logged out. Please log in again.