Find Jobs
Hire Freelancers

embedded Software design - ARM

£250-750 GBP

Cancelled
Posted about 9 years ago

£250-750 GBP

Paid on delivery
Required a firmware engineer with ARM experience. this is estimated to be a 2-3 month contract: the successful candidate will be given several prototype PCB samples and will be asked to do the following 1. ensure the PCB is functioning properly. 2. Specify and Write FW for the board based on requirements provided by the client. Work will be home-based. Required skills: 1. Embedded C/C++ experience 2. ARM experience (ideally Cortex M4) 3. Proven experience working directly with electronics with no OS is MANDATORY - all application without this skill will be rejected. 4. Ability to work directly with hardware with no support is required. Desired Skills: [login to view URL] ECG experience 2. Python-based programming
Project ID: 7339557

About the project

21 proposals
Remote project
Active 9 yrs ago

Looking to make some money?

Benefits of bidding on Freelancer

Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
21 freelancers are bidding on average £932 GBP for this job
User Avatar
Hi, i am a post graduate power electronics engineer and having very good experience in product design and development. I am good in power,analog,electronics circuits design and testing. i have a programmer,who is very much experience in C/C++ in pic,dsPIC, ARM controllers, AMTEL all .We both combine did many projects .I understand your requirement and ready to work for you. Please contact me for further discussion.
£555 GBP in 10 days
4.8 (50 reviews)
6.5
6.5
User Avatar
I am located in India and if you have no problems sending the boards to India then we can have a deal. I have good working experience on Cortex M4 (using GCC and Keil) and having 25+ years of experience in electronics and 18+ years in C programming. Literally I am practicing electronics since the age of 7 and I did my engineering in electronics as well. Lets discuss so that we can move forward. Thanks
£499 GBP in 10 days
5.0 (29 reviews)
5.6
5.6
User Avatar
I have experience with cortex M4 processors from freescale a lot, more then 4 years of developing low level FW like drivers and integration with MQX OS if necessary. Lot's of tools available : Logic Analyzer, Oscilloscope, Freq Counter, power supplys, JTAGs ... Check my previous work !
£833 GBP in 30 days
4.7 (5 reviews)
4.5
4.5
User Avatar
Hi, Working as a Freelancer consultant for the past 3+ years, with total experience of 9+ years in embedded systems in various phase of product life cycle. Worked on various 8 bit and 32 bit microcontrollers -- AT91RM9200, LPC2148, LPC1114, STM32F03, STM32F103, STM32W103, CC2538, CC2530, STM8S003, PIC12F1840, PIC16F84, PIC16F877A, PIC18F450, P89V51RD2, AT89C51, AT89S51 from these families -- Cortex M0, Cortex M3, ARM 7, ARM 9, PIC 12, 16, 18, STM8, 8051. Well equipped setup to test hardware and firmware. Could you please let me know the requirements of the client and the quantum of work. Please provide email id to see photographs of the current project. Thanks, Milind
£555 GBP in 10 days
5.0 (1 review)
2.5
2.5
User Avatar
Hi. We have written assembly and C for OS-less microcontrollers and DSPs for years. We have some experience with ARM. Actually I have a Cortex M4 board (TI Tiva C Launchpad) beside a number of other development kits. Have also done some assembly programming for Cortex A9, but not much. I've worked as a System&Applications and support engineer for Cirrus Logic DSPs. I have a personal 2ch PC oscilloscope and we can use my company's high-end Tektronix MSO4104 if needed. We also have experience in scripting languages like Python and TCL. What we do not have is medical ECG experience.
£555 GBP in 10 days
5.0 (2 reviews)
1.6
1.6
User Avatar
Hi, I have 5 years experience developing embedded software in C/C++. Most of the time, I developed bare-metal systems (without RTOS). I spent my first years on 32 bit SPARC architecture, before moving to 16 bit TI DSP C2800 architecture for the last 4 years. I uses Python and C# occasionally to create test scripts quickly for our devices. I started to play with ARM architecture recently. I played around with STM32 discovery, before moving to AT91SAM3X8E. I uses GNU Arm Tools with Eclipse. It works well with STM32 families, but it needs some effort to make it work with, let sat Arduino Due. At work, I occasionally uses scope, and on rare occasion, even soldering probe wire by myself. I not electronics engineer though. I am just an experienced embedded software engineer with scope. So, what do you attempted to do? What problem you're trying to solve? I am here to help you. Unfortunately, I can only commit myself to this project about 10-15 hours per week, due to my position as a full-time employee at local robotics company. I am looking forward to discuss this further with you. Thanks
£700 GBP in 135 days
0.0 (1 review)
0.0
0.0
User Avatar
****************************I AM READY TO WORK CAN HELP YOU VERY LOW BUDGET PLEASE CHAT ME***********************************
£250 GBP in 1 day
0.0 (0 reviews)
0.0
0.0
User Avatar
A proposal has not yet been provided
£555 GBP in 20 days
0.0 (0 reviews)
0.0
0.0
User Avatar
Dear Sir, I am pleased to bid for this project. I have a wealth of experience in embedded systems in both hardware and software. I have written firmware for self-test of microcontroller boards and very well versed with low-level assembly code and hardware troubleshooting. And I have very strong knowledge and experience in C/C++ programming. I have experience working for companies developing firmware for diverse set of applications like DVB/IP system, network router & industrial boards. I have worked on mbed / STM32 Cortex M3/M4 processors. I have personally developed STM32F103 based card and written firmware for data acquisition system running directly on hardware (super-loop), integrating device drivers for USB, micro SD card, timers etc. Also I have developed code for troubleshooting firmware crashes and logging. I can read circuit schematics and datasheets and will be able to work independently on hardware / firmware development. We can support you not only in development but beyond that will timely and reliable support after project is done. If you need further capabilities like OS / GUI integration, we bring to the table experience with RTOS like uCOS / FreeRTOS and Touchscreen GUI integration expertise. I can provide references for all of the work above in case you are interested. I am confident that my unique skill-sets will be of interest to you and you will consider me for the project. I assure you of our best service and attention at all times. You may revi
£500 GBP in 30 days
0.0 (0 reviews)
4.3
4.3
User Avatar
ARM experience with several different architectures: - ARM926-E (Atmel) - ARM Cortex-A5 & Cortex-A7 (Freescale) - ARM Cortex-A5 & Cortex-M4 (Vybrid) - iMX25, iMX57 - ARM Cortex-A8 (Beaglebone) Long experience with embedded systems, PCB reviews and BSP creation, including Linux and barebones. Used to work with no operating system (eg. MSP parts). Please note: The budget covers "standard" hardware setup (flash, RAM, USB, serial, i2c, spi...). For non-standard hardware, a specs review would be needed for budgetting.
£1,000 GBP in 30 days
0.0 (0 reviews)
0.0
0.0
User Avatar
hands on experience in troubleshooting electronic hardware and knowledge of programming embedded language
£555 GBP in 20 days
0.0 (0 reviews)
0.0
0.0
User Avatar
Hello, I have experience in C/C++, ARM Cortex-M processors and hardware programming with and without OS. I am currently working on a project that includes a NXP Cortex-M3 microcontroller. In this project, I am using Olimex JTAG, OpenOCD , gcc and code sourcery toolchain for code development. During my former project at permanent jobs, I have prepared hardware test documents, tested coming PCBs and some times, solved hardware issue. I am very familiar with hardware also. Kind regards, Cumali Ceylan
£500 GBP in 90 days
0.0 (0 reviews)
0.0
0.0
User Avatar
we need more details about the requirements to define the full steps and project milestones. you can contact us for more details about our team
£700 GBP in 90 days
0.0 (0 reviews)
0.0
0.0
User Avatar
UPDATE: I'm based in southern Germany on the border with Switzerland. Hello, I work in my day job with embedded devices, specifically medical imaging devices like endoscopes and colonoscopes that have ARM based control electronics. I use for development C (not C++) and a little assembly where is needed. As development environments I use mostly Eclipse with GCC and Keil MDK for Arm but I'm not afraid of building and editing a makefile by hand. Also I've written more than one interrupt routine. I have at home small but fully featured lab including a Tek scope, power supply, soldering and hot air SMD rework station and all that is needed for development. I also have experience with PCB design tools and I've made and soldered my own projects. I'm fluent in English and German, and by fluent I mean I can understand and communicate written and orally in all the technical issues. As I have no idea about the scope or extent of your project I can't offer you valid planning and a right set of milestones and just I've placed a generic bid, if you consider my bid please contact me first to clarify what you actually need. Best regards, Zevedei.
£722 GBP in 10 days
0.0 (0 reviews)
0.0
0.0
User Avatar
Dear Sirs, Thank you for inquiring the embedded software project. We believe we are the right partner for you, because I have got many years experience writing embedded software not based on particular operating systems like: - Watches and Calculators: different 4 Bit and 8 Bit MCUs - TFT LCD Controllers: ARM 7, Cortex-M3 - Digital Scales: Cortex-M0 and M3 - USB Bridges: Cortex-M3 Looking forward about more information. Kind regards, Axel
£570 GBP in 60 days
0.0 (0 reviews)
0.0
0.0
User Avatar
I am in the filed of embedded system over 10 years. I have work experience in making real-time embedded system (both software and hardware development). I think that I have all of your required skills. Examples of my projects: - Moving Robot for Object Tracking / Object Tracking With Stereo Cameras. I made PID controllers for servo motors (hardware and control software), Robot controller (hardware and software), Power Supply Unit, and PC Programs written by C++. - Education Robot I made Robot MPU Board, Step Motor Driver, Firmware(hardware control and robot program management) written by embedded C, and PC program. - Developing Hardware of Electric Power Steering ECU. I designed and developed hardware of Power Unit of the ECU, Sensor interface circuits, PM Motor Drivers and some control software. - Developing Software of Power Management ECU for Hybrid Vehicle. I designed and developed some software in the ECU such as Sensor interface Driver, a part of Platform Firmware, Hardware Diagonals, and etc.
£333 GBP in 7 days
0.0 (0 reviews)
0.0
0.0
User Avatar
Hi We can so you working prototype of my device with STM32F103RET6. We interfaced color lcd, sd card, usb, LAN, UART,I2S, SPI, I2C, FSMC, DMA, etc. please share some detail of work. so we can discussed further. Regards AEPSupport
£555 GBP in 30 days
0.0 (0 reviews)
0.0
0.0
User Avatar
Got embedded C/C++ experience (ARM 1176JZF-S, Cortex M4, Cortex A8, VLSI VS1005). Wrote firmware for few electronic products - see my profile. Two of them got Linux, the other two were without any OS.
£7,500 GBP in 90 days
0.0 (0 reviews)
0.0
0.0

About the client

Flag of UNITED KINGDOM
United Kingdom
0.0
0
Payment method verified
Member since Mar 20, 2015

Client Verification

Thanks! We’ve emailed you a link to claim your free credit.
Something went wrong while sending your email. Please try again.
Registered Users Total Jobs Posted
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Loading preview
Permission granted for Geolocation.
Your login session has expired and you have been logged out. Please log in again.