Amplifier design

Completed Posted Dec 23, 2014 Paid on delivery
Completed Paid on delivery

I have a frequency generator that has a 5amp power supply with 5+,5-,common.

I need an amplifier of the signal that has a channel 1&2 passing through an opamp before reaching the potentiometer then output. Ch1 and Ch2 is 180 degree out of phase.

The input to amplifier will range in frequency to the max of 25mhz and 0.05v to max 8v signal peak to peak. The output will run a coil of 0.5ohm and we can have a 10w10ohm resistor to limit the sort circuit.

The frequency generator is giving a modulated sign and sqr wave.

1. Fundamental: from 0.5 to 1.6mhz - sign

2. 1 to 11th harmonic - sqr

3. 3.1mhz carrier wave - sqr

I need an output of 20volt peak to peak so a step-up is needed.

Look at this: [login to view URL]

at the page 47 you have boost amplifier that maybe could good for the application

Pcboard design, layout, bom and gerbers are required for me to manufacture a sample to test your design.

Space in limited in my enclosure and i need to know what heat sink to use.

Circuit Design Electronics PCB Layout

Project ID: #6899170

About the project

12 proposals Remote project Active Jan 1, 2015

Awarded to:

pcbdcs

Hello, I have been associated with Hardware design (Circuit / Electronics design), PCB design, PCB Manufacturing, Component procurement, PCB Assembling and Functional testing for over 7 years. I have used various C More

$150 USD in 3 days
(124 Reviews)
6.7

12 freelancers are bidding on average $154 for this job

uetian09ee506

I am working as Lab Engineer at FAST National University Pakistan, in Electrical Department, I have conducted the followings Labs, and also supervised Projects related to these labs. 1. Control System Design & Mode More

$155 USD in 3 days
(195 Reviews)
6.8
cscinstructor

I have read and understood your requirements.. Please open chat to discuss further… ++++++++++++++++++++=======================================++++++++++++++++++++++++++

$200 USD in 3 days
(17 Reviews)
5.0
ShaheerJaan

Hi. I am a professional Electronics Engineer having expertise in Electronics Circuit designing and in amplifier designing as well. Contact me.

$130 USD in 3 days
(13 Reviews)
4.1
saipanjiguly

Have industrial experience in PCB designing. Have worked on many embedded projects : coding and hardware designing. Have 4+ years experience in KiCad. Worked on many modules like SIM908, Nordic nRF51822, CY7C65632 and More

$100 USD in 5 days
(7 Reviews)
3.6
buddyatwork

Dear Sir, in the page no of the data sheet you have mentioned there are +15 and -15 V supply voltage. So the output voltage of 10 V is well within the band. But in our case the maximum supply volatge is +5V and -5V. So More

$111 USD in 3 days
(2 Reviews)
2.5
keyurpatelel

A proposal has not yet been provided

$155 USD in 3 days
(0 Reviews)
0.0
vishalsuryawansh

A proposal has not yet been provided

$172 USD in 4 days
(0 Reviews)
0.0
aseesahmed19

A proposal has not yet been provided

$173 USD in 3 days
(0 Reviews)
0.0
runner11

Hi, I am an Electrical Engineer and expert in circuit designs PCB layout. I have done many projects of amplifier designs for my own projects. I assure your I will complete the project according to your requirements .Th More

$95 USD in 6 days
(0 Reviews)
0.0
fduhia

Hello, I would like to register my interest in your project. I am a trained Communications and Electronics engineer with experience in circuit analysis and design. As per your specifications, I believe the following de More

$155 USD in 3 days
(0 Reviews)
0.0