PCB Layout Jobs

I already have the mechanical outline captured in a DXF file; what I need now is a matching PCB-layout template inside Altium so I can reuse it across future designs. Once the template is ready, I’ll hand over two existing Altium projects. Your job is to drop each board onto the new template and enlarge the four mounting holes (current drill size will be in the files; target size we can confirm together before routing). Key points you will handle • Import DXF, create the board shape, keep all layer names, stack-up and grid settings tidy so the file shows up as a clean “PCB layout template” in Altium. • For the two boards, migrate them to the new template and update the mounting holes only—no component relocation or net changes expected. • Retur...

I'm looking for an experienced PCB designer to integrate several components for a control system product. The PCB will be powered by DC and should be of medium size. Key components to integrate: - SIM module - PZEM modules - ESP32 - LCD display module Ideal skills and experience: - Proficiency in PCB design software - Experience with integrating multiple modules - Knowledge of DC power systems - Ability to design medium-sized PCBs Please provide examples of past work and relevant experience.

I’ve completed the physical shell for a phone case with a built-in drawer. I now need a freelancer to design and prototype the **electronics + firmware** that detects drawer activity and reliably sends events to the phone/app which I have already developed. (what I need built): * Recommend the best sensing approach to detect **drawer open/close** (magnetic reed/Hall, microswitch, optical, etc.) and design around the case constraints. * Select components and create a complete electronics design: * **Low-power microcontroller + BLE** (or comparable phone connectivity) * Sensor(s) for drawer state * Battery + charging solution (or wired power if strongly recommended) * LED indicator (subtle, optional but preferred) * Provide: * Schematic, BOM, and PCB layout (compact, manufacturable...

I have a device that runs on 12-48v DC, drawing up to 5A at 12v at bootup. This then settles down to 2-3A for normal operation. I need to run this device from my 12v vehicle battery – either via a cigarette lighter plug or direct battery connection. The device runs fine at 12v, but runs better at a higher voltage. The device’s supplied 240v power supply outputs 30v @ 2.0A/60W. The problem is that when the vehicle engine is started, the current drops and the device reboots. I need a circuit and PCB design that will: a) Be robust enough to live in a vehicle b) Switched (off board) – via screw terminals c) Fused (either on PCB or automotive blade fuse connected to PCB via screw terminals) d) Reverse polarity protection e) Reverse connection protection (i.e. po...

I need a double-sided, plated-through-hole PCB for a scientific-industry device. The finished board must fit within 100 mm × 100 mm and be delivered as a complete Altium Designer project. Here is what I will provide once we start: the schematic, mechanical outline, and any component datasheets that are not already in common libraries have a Physical PCB board With Simple Design ( Round Cut PCB size 70 x 70 mm ). Your task is to translate that data into a clean, manufacturable board, route all signals with proper clearances, and prepare fabrication outputs. Deliverables • Altium .PrjPcb with all libraries embedded • Gerber X2, drill and pick-and-place files, ready for immediate fabrication • PDF plots (schematic and PCB) for quick review Acceptance criter...

Building a Catholic Prayer Chime Device — Electronics Design Phase We are developing The Angelus Chime, a battery-powered devotional device that plays authentic church bell recordings at 6 AM, 12 PM, and 6 PM. This is Phase 1 focusing exclusively on electronics design. IMPORTANT: This engagement delivers DIGITAL FILES ONLY — No physical prototypes, no assembly, no enclosure work. DEVICE OVERVIEW A sacred object for the home — a device that rings real church bells three times a day, as they have for 700 years across Europe. No app, no WiFi, no Bluetooth. Just bells. CORE FUNCTIONALITY Plays 2-3 minute church bell recordings at prayer times 3 toggle switches for each prayer hour Rotary switch for 8-12 bell recordings on SPI flash Volume control + large mute button Tim...

I am seeking a US-based hardware developer or electronics technician to assemble two physical prototypes of an RF-based proximity system. I have already developed the full source code and circuit schematics; however, due to a physical disability, I require a partner to handle the soldering, wiring, and physical housing of the components. Technical Requirements The project consists of two separate units: a Transmitter and a Receiver. Microcontrollers: Program and integrate 2x Arduino boards (provided/specified in schematics). Connectivity: Configure RF modules for proximity detection. Power: Integrate rechargeable battery systems (Li-Po or similar) with charging ports for both units. Assembly: Solder all components according to provided schematics. Enclosure: Mount...

1) Project goal Design a single PCB device for testing cable harnesses up to 25 wires, where both ends of the same harness are connected to the board: Side A: 25 lines (A1..A25) Side B: 25 lines (B1..B25) Total: 50 signal lines on the PCB. The detailed test logic (continuity/shorts/mapping) will be implemented in firmware later. For this phase, the key deliverable is robust hardware (schematic + PCB) prepared for such testing. 2) Scope of work (hardware only) Electrical schematic PCB layout Production files: Gerbers + drill BOM (with specs and acceptable alternatives) Assembly files (pick&place/positions) preferred Short mapping table: MCP23017 pins → A/B line numbers (Firmware is NOT required in this phase. Optional “I2C scan / basic blink” is a bonus.) 3...

I need an embedded engineer to help safely connect a PCB to a lead-acid battery pack in series and integrate 4 external sensors (temperature, humidity, water presence, etc.). The system must read data in Arduino IDE and, if possible, send it to an existing telemetry endpoint (HTTP/MQTT). Scope: Safe wiring from battery pack to PCB Best way to connect and mount sensors Connector and grounding recommendations Simple Arduino example to read sensors and output/send data Experience with ESP32, Arduino, sensors, and battery-powered systems required.

I am midway through an online electrical training program and still have two graded components left in each module: the “learning activity” and the “content quiz.” Both are multiple-choice, can be retaken without limit, and I need a final score of 90 % or higher on every attempt that counts toward my record. You will receive screen-shots of every unfinished unit plus login access so you can work directly in the platform. Feel free to lean on AI tools or any personal reference material; the school places no restriction on outside resources. When you reply, please mention any hands-on electrical background, coursework, or certifications that show you can navigate these topics confidently. Deliverables • All remaining learning activities submitted with ≥...

I’m looking for an experienced electronics designer to develop a complete industrial-grade control system consisting of two devices: 1. Transmitter (TX) – collects inputs from joysticks and other signals (8 analog + 2 digital + AUX). 2. Receiver (RX) – receives data from TX via CAN and drives power outputs. Communication between TX and RX must be via CAN bus. The system must operate on 12V or 24V vehicle/machine installations, with a supply range of 9–27V DC. Scope includes schematic design, SMD PCB design, and enclosure selection/design. ⸻ Functional Requirements TX (Transmitter) • 8 analog input channels (joysticks / analog signals) • 2 digital inputs • 1 AUX signal (logic/auxiliary) • Analog measurement must use an industrial-grade ...

I need a purpose-built Wi-Fi modem that can sit in the field, discover and manage between twenty and thirty of my smart prepaid electric meters at once, then forward their information to a third-party server. Core requirements • Meter side: maintain a stable local link to each prepaid electric meter, poll at configurable intervals, queue data when the Wi-Fi link is down, and reconcile immediately after reconnection. • Network side: connect via standard 2.4 GHz Wi-Fi, authenticate securely (WPA2 minimum), and push three distinct data streams—usage statistics, diagnostics snapshots and real-time alerts—through the API endpoints I will supply. • Throughput: normal operating load is small, but latency for real-time alerts must stay below two seconds under fu...

Seeking experienced hardware engineer to build a prototype of a wall-mounted emergency device. Specs: Form Factor: Wall-mounted, compact, durable enclosure (weatherproof if outdoor use intended). Primary Function: Transmit pre-programmed GPS coordinates to a central monitoring location (e.g., server, app, or emergency service) upon activation for real-time tracking. Transmission Methods: Primary: GSM (cellular network) for cost-effective, low-latency sending. Failover: Satellite (e.g., Iridium or Globalstar network) if GSM unavailable. Power Source: Battery-powered with optional mini solar panel for recharging. Standby Battery Life: Minimum 1 year without charging (low-power mode). User Interface: Single button for activation; 2 LEDs for status feedback. Key Features Programming: Devic...

My 4.5 V circuit needs a small solar panel and the proper charge-management hardware so daylight tops the battery up automatically. I’m not sure what panel voltage or wattage is best, nor which controller IC will keep the Li-ion safe—so I need your electronics expertise. Scope of work – I'll share my schematic of the existing 4.5v circuit – Select or design a charge-controller stage that handles lithium-ion chemistry, prevents over-charge/over-discharge, and outputs a stable 4.5 V rail to the load. – Provide a clear schematic, concise BOM with part numbers that are easy to source, and wiring instructions I can follow on perfboard or a small PCB. – Advise on any protection components (diodes, fuses, reverse-polarity safeguards) so the device...

Project Description: I'm building a compact, consumer-grade handheld device that hosts multiple ARM processors and modules on a single 4-layer board. The design must accommodate a high-speed USB hub, balanced power distribution, and impeccable signal integrity without exceeding the layer budget. Components to Integrate: Component Details Interface Luckfox Lyra Zero W ARM Cortex-A7 Linux SBC (65×30mm, 40-pin header) Direct solder or socket Teensy 4.1 ARM Cortex-M7 @600MHz audio DSP (61×18mm) 2.54mm headers SL2.1A USB Hub IC 4-port USB 2.0 hub Surface mount XIAO ESP32S3 LoRa module (21×18mm) 1.27mm headers STM32WB55 Module Dual-core ARM Cortex-M4/M0+ (Flipper brain) 8-pin header PyBoard v1.1 ARM Cortex-M4 backup controller 6-pin header GPS Module NEO-6M/8M 4-pin heade...

I need an experienced electronics / PCB engineer to design a reliable 24/7 traffic light controller PCB. This is a safety-critical industrial system, not a hobby project. System Details: 220VAC traffic light LED modules Control via TRIAC (optocoupler + TRIAC driver) Continuous 24/7 operation ESP32-based control Fail-safe design required Industrial-grade AC mains design Using EasyEDA Requirements: Strong ESP32 hardware experience Experience with AC mains / TRIAC design Experience with industrial / high-reliability systems Comfortable designing fail-safe protection systems Timeline (strict): Day 1: Complete schematic Day 2: PCB placement & routing If it takes longer, it means you are not experienced enough — this is not a complicated project. You must be ready to...

I need the 2026 GC front panel converted into a production-ready Gerber package so my board house can mill an exact aluminum faceplate. All mechanical data are already prepared: you’ll receive a clear photo of the current panel plus an Excel sheet detailing every cut-out, hole diameter, and positional coordinate. No circuitry is involved—this is purely a mechanical PCB. Here’s what I expect: • A clean RS-274X Gerber set, including drill file, that matches the spreadsheet dimensions to the tenth of a millimetre. • A simple PDF drawing or fabrication note that calls out all critical sizes for one last visual check before I release it to the shop. Please stick to the manufacturer’s standard rules; I’ll share their design-rule file once we start, ...

I need a medium complexity (3-4 layers) PCB designed for signal processing. The design should be capable of accommodating surface-mount components. Requirements: - 3-4 layers PCB design - Signal processing functionality - Surface-mount component integration - Gerber file generation Ideal Skills: - Experience with PCB design software (e.g., Altium, Eagle) - Strong understanding of signal processing circuits - Proficiency in layout for surface-mount components - Attention to detail and accuracy Please provide samples of previous work.

I have a finished KiCad PCB layout and now need a clean, print-ready PDF compiled from it. The final document must contain six A4 landscape pages arranged in this exact order: 1. Copper Top Layer 2. Copper Inner Layer 1 3. Copper Inner Layer 2 4. Copper Bottom Layer 5. Component Placement Top Layer 6. Component Placement Bottom Layer Resolution has to be crisp enough for both close-up review and high-quality printing. I’ll provide the KiCad source files as soon as we get started; you simply export each required layer, keep KiCad’s default rendering colours, and merge them into a single PDF. I’ve attached a previous example—please note the labels are mirrored on that file due to an earlier issue, so yours should read correctly. Deliverable • O...

Hello, I am looking for an experienced PCB designer to complete schematic review and PCB layout for an ESP32-based industrial IoT board using EasyEDA (Collaborator mode). Scope of Work 1. PCB Outline & Mechanical Alignment The PCB outline must match an existing device layout based on measurements and connector positions that I will provide. There is no reference Gerber file, so the board outline must be recreated carefully and confirmed with me before routing. 2. Schematic Review & Improvement (Important) You must review the schematic and confirm it is electrically correct and suitable for stable operation, including: Component ratings verification Power design validation Decoupling and grounding ESP32 stability considerations LM2596 switching regulator layout considerations Identi...

I'm seeking an experienced PCB designer to create a double-layer PCB for a consumer electronics radio project. The PCB will include microcontrollers as key components. Key Requirements: - Design a double-layer PCB - Incorporate microcontrollers into the design - Suitable for consumer electronics use Ideal Skills and Experience: - Proficiency in PCB design software (e.g., Altium, KiCad) - Experience with double-layer PCB design - Knowledge of microcontroller integration - Background in consumer electronics Please provide samples of previous work and relevant experience.

I need an existing wiring schematic revised to add one component. Requirements: - Current schematic is scanned from PDF - Need to add a green pilot light Ideal Skills: - Experience with wiring schematics - Proficient with PDF editing and schematic modification - Attention to detail and accuracy

Custom TWS Earbuds Prototype - Earin M-2 Miniaturization** UNIVERSITY PROJECT: Redesign Earin M-2 earbuds SMALLER to reduce ear protrusion. CURRENT SPECS: 24×15×15mm shell, 4g each, 60mAh battery, 4hr playback, BA driver, NFMI sync, touch controls TARGET SPECS: <20×13×12mm shell (33% smaller volume) • Same features or close equivalents • 1-2 FULLY WORKING prototype pairs DELIVERABLES REQUIRED: 1. New shell design (3D printed or molded) 2. Custom PCB layout for reduced volume 3. Component sourcing (mini BA driver, BT/NFMI, 40-50mAh battery) 4. Full assembly + functional testing 5. Audio test + TWS pairing validation I HAVE: • Complete Earin M-2 teardown photos • Exact measurements + target dimensions • Protrusion problem photos &bu...

I am developing a compact handheld consumer device prototype that requires integration of a rechargeable battery and small electronic module inside a custom 3D printed enclosure. I am looking for an experienced embedded hardware / electronics engineer who can help design and prototype a small, safe, battery-powered system suitable for a handheld form factor. The device will require: • Integration of a rechargeable lithium battery (3.7V or similar) • Safe charging system (USB-C or similar) • Small heating or vapor-generating element OR similar compact load component • Efficient power management and protection circuitry • Compact PCB design suitable for fitting inside a slim enclosure • Guidance on component selection and prototype assembly The enclosur...

I new to design a PCB dedicated to processing several signals and starting a device based on a set number of conditions. I would like to be able to modify those parameters from a cloud based or simple web interface. The board should handles both analog and digital. I expect all to be digital signals but just in case. It should basically handle, temperature, humidity and time of day. Deliverables 1. Compiled firmware binaries plus full, buildable project files 2. Clear inline comments and a concise README explaining build steps and pin mappings 3. A short test report that documents signal-integrity measurements and confirms the module meets the agreed specs. 4, Plus device recommendation and also help on setting up. I have an idea, but I am a genetic engineer. I am OK with basi...

I already have the full schematic and the finished PCB files for a board that combines an ESP module with a PIC18F microcontroller. What I’m missing is a clear, practical explanation of how everything talks to each other, especially over UART, and how that interaction is implemented on the physical board. Here is what I need from you: • A step-by-step walkthrough of the signal paths that handle UART traffic between the ESP and the PIC18F, including any level-shifting, buffering, or hand-shake lines that support the link. • A guided tour of the PCB layout that shows where those signals travel—layer changes, vias, ground references, decoupling, and any routing choices that affect integrity or noise. • Simple notes on any supporting circuitry (power rails, ...

I already have the full schematic and the finished PCB files for a board that combines an ESP module with a PIC18F microcontroller. What I’m missing is a clear, practical explanation of how everything talks to each other, especially over UART, and how that interaction is implemented on the physical board. Here is what I need from you: • A step-by-step walkthrough of the signal paths that handle UART traffic between the ESP and the PIC18F, including any level-shifting, buffering, or hand-shake lines that support the link. • A guided tour of the PCB layout that shows where those signals travel—layer changes, vias, ground references, decoupling, and any routing choices that affect integrity or noise. • Simple notes on any supporting circuitry (power rails, ...

I’m replacing my existing pool circulation unit with a single-speed pump that I already have on site, along with all the fittings, unions, and electrical hardware required. The pad is clear, the plumbing is exposed, and access from the driveway to the equipment area is wide open, so getting tools and materials in place will be straightforward. What I need is a qualified installer who can: • Plumb the new pump into the current PVC line, ensuring airtight, leak-free unions • Make the electrical connection to the existing breaker, verify correct voltage, and bond/ground to code • Prime, test-run, and fine-tune the flow so the system reaches full pressure without cavitation • Leave the pad clean and walk me through basic operation once everything is running sm...

I need a detailed wiring diagram to support a building permit application for a five electrical panel system at an apartment building in Huntington Beach, California. Requirements: - Must be a wiring diagram - Includes main electrical feed into the apartment and 5 separate electrical panels - Must include panel numbers and locations Ideal skills and experience: - Expertise in creating electrical wiring diagrams - Knowledge of building permit requirements in California - Experience with multi-panel electrical systems Please provide a sample of similar work done.

I’m developing a compact medical-grade board that will sit at the heart of a new vital-signs monitor. The PCB must reliably acquire and process heart rate, blood pressure, and respiratory rate signals, then pass the data to a microcontroller for further analysis and display. Here’s what I need from you: • Complete schematic capture based on my sensor and MCU selections • Four-layer board layout optimized for low-noise biomedical signals (Altium or KiCad preferred) • Manufacture-ready Gerber files, pick-and-place data, and a clearly structured BOM with medical-grade component choices • Design reviews at schematic and pre-release layout stages so we can make sure the board meets IEC 60601-1/-2 spacing, leakage, and isolation requirements • Brief ...

I need a PCB designed specifically for a one-off project; it is not part of a commercial product line, so flexibility and creativity are welcome. The board will carry only analog circuitry—no digital sections—centred around operational amplifiers and a small signal-processing stage I will detail once we start. What I will supply: the schematic (PDF or KiCad), preferred footprints, and basic mechanical constraints. What I need from you: a clean, manufacturable layout with proper analog grounding practices, complete Gerber/ODB++ files, a reviewed BOM, and the original design file so I can revise it later if needed. Please aim for standard two-layer construction unless you advise otherwise for noise reasons. Acceptance will be based on: • DRC-clean files that import i...

The task is to design a compact PCB that drops straight into an SCX 1/32 car so it can run on a digital track. I want the board to read the track’s reed-sensor signal, let me assign any of 20 unique car IDs in firmware, and expose a surface-mount USB-C port on the edge for easy flashing once the body shell is back on. Size must stay close to the original analogue board footprint (about 24 × 18 mm, height under 6 mm) but I can adapt mounting holes or connector positions if you have a cleaner layout idea. Power comes from the standard track pickups (nominal 14–18 V DC), so include an efficient buck or LDO to feed the microcontroller and reed circuitry. I haven’t locked the MCU yet; pick anything small, inexpensive, and easy to program—ATmega, STM32, ESP32, or s...

I’ve drafted a single-layer board in Altium Designer and now need a seasoned set of eyes to run thorough simulations before I commit to building the first prototype. Your task is to import my project, verify the stack-up and component models, and perform all relevant electrical, thermal, and rule-check simulations available in Altium. Key goals • Confirm that signal integrity and power distribution meet design intent. • Flag any DRC or manufacturing issues early so I can correct them before fabrication. • Produce a concise simulation report summarizing the tests run, key plots or screenshots, and your recommendations. Deliverables 1. Updated Altium project files with all simulation settings preserved. 2. PDF or DOC report of findings and suggested fixes. ...

I need a clean, well-structured Process Flow Diagram for an Oil and Gas Manufacturing Company that will be used primarily as a training and instruction aid for operators and new hires. I already have the P&ID sets that will be used as the basis in digital form, so you can start by refining and reorganising that file rather than drawing every symbol from scratch. The job is straightforward: translate the existing digital schematics into a single, professional-grade PFD with clear tagging, line weights, and legend so it is easy for a trainee to follow. Consistency of instrument symbols, line numbering, and valve identification is critical because this graphic will be embedded directly into our training manuals. Please work in any mainstream CAD platform you are comfortable with&mdash...

I need a detailed electrical plan for installing an EV charger in the garage of a new residential home, as required by council regulations. The home has a three-phase electrical supply. Requirements: - Compliance with Woollahra council regulations For condition 14 (Item 37) that requests “electrical plans of all off street parking demonstrating capacity for Level 2 (single phase, 7kw power) charging point” - Detailed schematics for three-phase supply - Specifications for EV charger installation in garage Ideal Skills and Experience: - Experience with residential electrical planning - Knowledge of council requirements for EV charger installations - Familiarity with three-phase electrical systems

I need a compact, production-ready circuit that brings reliable wireless communication to a new consumer-electronics device. The work begins with schematic capture and component selection, moves through PCB layout, and finishes with ready-to-manufacture Gerbers, a complete BOM, and clear test guidelines. The radio link is the heart of the design, so careful RF layout, antenna matching, and regulatory-compliant power levels are essential. Bluetooth LE is my preferred protocol, though I am open to Wi-Fi or other 2.4 GHz solutions if you can demonstrate lower cost or better battery life without sacrificing performance. Please plan on: • Delivering editable design files in Altium, KiCad, or Eagle, plus PDFs for quick review • Calling out any critical components with long le...

Please Sign Up or Login to see details.

I want to build a compact, two-way Bluetooth audio interface for a HAM radio. The core goal is a 2-way bridge between the radio and a realtime camera running on a linux board via buletooth. Digital or analog volume adjustment is needed Device must be battery and/or 12V DC operated, with DC12V charging battery if present What I need: • Full-duplex transmit and receive so both the radio’s microphone and speaker lines travel over Bluetooth. • A design that plays nicely with typical HAM radio mic/headphone levels. • Optional Radio PTT Sense to mute microphone input if PTT button not pressed • Stable pairing, clear voice quality, and minimal latency. Please provide: 1. Schematic and bill of materials (module choice is up to you; CSR, ESP32, or similar is fine). 2...

I’m putting together a compact desk ornament that spins on command, and I need a complete PCB solution to drive the rotation reliably. The ornament will only move when a small switch is flipped—no sensors, no remotes, just simple manual control feeding a quiet motor. Main Features: • main power source is 5V from USB to DC power jack connected to board via JST-PH cable 2pin socket. • 3.7V 800mAH Lithium chargeable battery as backup power source, connected via JST-XH cable. • 3-way SPDT switch(on, off, timer) connected to the PCB via a JST-XH cable. • 3V DC motor with peak current around 3A, connected to board via JST-PH(2pin) • 2 mounting points (M3 size to allow M2.5 bolts) Here’s what I’m after: • Schematic and PCB layout for a ...

PCB Technical Blog Writing Guidelines Each week I publish in-depth, EEAT-driven articles that demystify printed-circuit-board design and manufacturing for an audience of intermediate professionals. The primary goal is to educate—every post must read like it was penned by someone who has actually laid out boards, debugged traces, and wrestled with impedance calculations, not by a generic content mill. Scope of work You will draft original how-to guides that walk readers through real engineering challenges (e.g., stack-up selection, thermal relief strategies, DDR routing tips). Practical detail and accurate terminology are essential; surface-level summaries or re-hashed competitor pieces won’t be accepted. Quality standards • EEAT: demonstrate personal experience,...

Projeto: Engenharia Reversa de Placa Eletrônica Legada Descrição do Projeto Busco profissional com experiência comprovada em eletrônica para realizar engenharia reversa completa de uma placa eletrônica legada, com o objetivo de: Reproduzir fielmente o funcionamento elétrico original Modernizar componentes obsoletos Gerar documentação técnica completa e atualizada Garantir compatibilidade mecânica, elétrica e funcional com o equipamento original O projeto seguirá um procedimento técnico estruturado já definido internamente Escopo do Trabalho O profissional deverá executar as seguintes etapas: 1. Análise e Correlação do Esquemático Verificaç&...

Ho già costruito alcuni prototipi di un circuito in grado di commutare un’unica linea da 230 V, 16–30 A, verso 4, 8 o 12 uscite; --senza perdita di potenza--, nessuno, però, raggiunge ancora gli standard che mi aspetto. Dispongo di schemi, calcoli, misurazioni termiche e log di prova: materiale sufficiente per chiarire ogni dettaglio tecnico e velocizzare il tuo lavoro. Mi occorre un progettista senior che sappia trasformare tutto questo in una soluzione definitiva, completa di firmware su ESP32, con PCB multilayer (4 o 6 strati, produzione JLCPCB - copper 3once) e una simulazione accurata e documentata prima della produzione. Requisiti tecnici da rispettare • Massima efficienza energetica, protezione dei componenti e precisione nella commutazione sot...