Creating and Using Modules in JavaScript
Ways to define and use JavaScript modules in your projects
I am looking for a construction project manager. Someone who can read drawings, ensure the subcontractors are completing their work properly, ensure project is on/under budget, coordinate material deliveries. I was selected to build an addition at a restaurant just outside philadelphia. The project should take approximately 4 months and is scheduled to begin in 2-3 weeks.
I have a small project for a charity where I need a bricklayer to build an outdoor cooker. They need to build a concrete base and then build a circular fireplace with the following dimension: 116cm dia/ 25cm high and another 60cm dia/ 20cm high. I will offer all the materials and I have a wide range of tools and a staff to support this work.
I have an adapter made to adapt an engine to transmission (A), but I want to create two engine adapters to adapt transmission (B) and transmission (C) to the engine instead. I am located in Maryland (USA) and will not ship the components to any location, but willing to drive the components within a reasonable distance for the scans to be completed.
We have a vacant lot under contract in Palm Harbor, FL and there is a drainage pipe in the middle of it. We learned that it is the drainage pipe for all the houses on the street. The county said its only buildable if it can be moved, directly from the DRS Manager, "Unless they have a civil engineer design a new stormwater management system for the subdivision, the lot remains undevelopable." So, we would like to see if this is possible and if so, what the approximate cost would be. Thank you.
1 roof plan of “kansai international airport” with all details (hvac, thermal ins, dimensions, materials, name of materials) - scale 1/20 2 sections from the roof only - with all details (thermal, dimensions, materials, name of materials) - scale 1/20 And 5 point details with plans , from the roof itself , with all the details , materials, name of materials , hatches and screws or other materials with is holding the roof together. - scale 1/20 All must be done in autocad. I have 1 section and 3 point details at the moment (without the details) you may continue with what I have or you can start from the first. Whatever you wish. DEADLINE: 21 MAY 2022
A two-storey house in Sunshine Coast, QLD has been planned to have a terrace over garage which is supported on a concrete beam and two columns at front of the garage. The principal engineer has proposed to use 32MPa concrete (unit weight 25kN/m3) for this building. You are required to analyse and design RC Beam carrying the load of terrace of this building by solving Tasks 1 to 21. Include references from Australian Concrete Standards (AS3600-2018) where possible. The required design data is given below. 3. Determine the magnitude of the ultimate design load w* 5. Determine the short-term bending moment ??∗ 4. Determine the design bending moment M* ?? 6. Determine the long-term bending moment ??∗ ?????? 7. Determine the area of steel required for the calculated M*
I have to have a Parcel map created for a new 5000 sq ft parcel that I am creating by splitting my existing property parcel in a 60/40 ratio. The new parcel comprises 40% of the existing parcel. The surveyor/engineer needs to be licensed in the State of California.
18/05203/FUL | Part demolition, partial retention of the front elevation and a rebuild of the site for the conversion of 1 residential unit at first and second floors into 4 self-contained units: 1 x 1bed and 3x 2bed units involving the demolition of the existing first floor storage room and the erection of a rear extension at first and second levels and two additional storeys including the formation of a lightwell together with fenestrations alterations at the front elevation and the relocation of a rear extraction flue and staircase serving the existing commercial unit and the provision of cycle and refuse storages at ground level. A replacement shop front and the relocation of an existing front main entrance to the residential units. | 48 Kennington Road London SE1 7BL
I'm interested in a TEAM of two to four that can work on Auto CAD for construction documents for New three-story high residential building. I have all the designs completed; floor plans and elevations. I would need extra construction which I will discuss/explain to each freelancer. There is no budget, the freelancer will review what I need and the duration that I require, and we would discuss the fee.
Need structural engineer to review housing plans that involve, Insulated Concrete Forms- Concrete footings, for rebar reinforcement, possible Helix Micro Rebar prescriptive method. Roofing Rafters, Roof sheathing, LVL and of lap slicing of long lumber runs. Engineering must be quoted, and final engineering stamped by licensed engineer in the state of Maryland.
Ways to define and use JavaScript modules in your projects