Plc scada jobs
I need a complete SCADA-PLC program built on Siemens hardware and software. The process itself is already mapped out; what I’m missing is the logic, HMI screens, alarms, and basic data logging that tie everything together. Scope • Develop and document the ladder logic / TIA Portal project. • Design intuitive SCADA screens with key process indicators, start-stop controls, and alarm pop-ups. • Configure alarms, interlocks, and safety routines in line with the existing I/O list. • Set up basic historical data logging so operators can review trends. • Provide an offline simulation or short video walkthrough so I can verify functionality before site deployment. Requirements • Must use Siemens PLC and HMI software (TIA...
I’m looking for a seasoned Omron PLC specialist to locate and correct faults inside an existing program that is already running on site, in Adelaide South Australia. The core of the assignment is pure debugging—no new hardware, no ground-up rewrites—just smart, efficient troubleshooting of the current ladder / structured-text logic so the machine can run reliably. What I expect from you: - Be local to Adelaide South Australia • Analyse the uploaded CX-Programmer or Sysmac Studio project, reproduce the reported issue, and pinpoint its root cause. • Rewrite or adjust the affected rungs, function blocks, or tags to eliminate the fault while preserving the rest of the logic. • Compile and download the updated code (either through a remote session or...
...reliability. Troubleshoot robot paths, safety circuits, and communication interfaces. Collaborate with PLC, tooling, and process teams to ensure synchronization between robot and line operations. Document configuration changes, backup robot programs, and support customer handover and training. Qualifications Bachelor’s degree in Mechatronics, Electrical, Mechanical, or Automation Engineering (or related field). 3+ years of hands-on experience in robot commissioning, programming, or debugging in automotive production environments. Proficiency with ABB, Fanuc, KUKA, or Yaskawa robot systems. Familiarity with OEM technical standards (Tesla, GM, Ford, Stellantis, or similar). Understanding of robot–PLC integration, fieldbus networks (PROFINET, Ethernet/IP),...
I need a PLC-driven solution that boosts overall system performance by automating the way we capture and log flow-rate data. The current setup delivers only basic readings; I want reliable, real-time information that can be stored, trended, and served to our SCADA or historian without manual intervention. Scope • Assess the existing instrumentation loop and PLC I/O. • Design a detailed plan for flow sensor integration, wiring, and any signal conditioning required. • Develop and document PLC logic to collect, time-stamp, and buffer flow-rate values. • Configure communication so the data reaches our central database (Modbus/TCP or OPC UA—open to your recommendation). • Supply a functional prototype program with clear comment...
...stream, inspects the texture of product (dewatered potato pulp) moving on a conveyor belt (or in a screw converyor), and decides whether that material is wet or dry. See images. It is also possible to give more close up images of the product on the conveyor belt or during the overflow. Once a decision is made the software must immediately do two things: • push a flag we can read inside the PLC/SCADA layer so the process can react (speed change, diverter, etc.), and • raise an operator alarm whenever the state flips or a confidence threshold is not met. Key points you should know • Source feed: live RTSP stream served by our Unifi NVR. No file uploads—the analysis has to run continuously. • Core technique: texture analysis. We already ha...
...________________________________________ Qualifications and Experience • Minimum HNC qualification (or equivalent in Engineering or Maintenance discipline). • Proven experience in a processing or manufacturing environment, ideally within the food or feed sector. • Good knowledge of mechanical and electrical systems (motors, conveyors, pneumatics, pumps, sensors, etc.). • Familiarity with control systems, PLC fault finding, and automation is advantageous. • Working knowledge of LOLER, DSEAR, PUWER, and quality management systems such as FEMAS and ISO. • Strong fault-finding, problem-solving, and communication skills. ________________________________________ Working Pattern • Shift-based working pattern to support 24/5 (and occasional weekend) ope...
I’ve built the first release of the KnifeBox control system on an Omron NX102 with two 1S servos over EtherCAT and an NB5Q HMI on EtherNet/IP. Before moving the machine to production, I want a seasoned set of eyes to go through my work focusing primarily on code structure and logic flow, with special attention to making the program more modular. Here’s what I’d like from you: • Walk through the Sysmac Studio project, validate the overall architecture, and pinpoint functions or programs that can be refactored into reusable modules without sacrificing execution speed. • Confirm that motion‐related FBs, axis interlocks, and enable chains are arranged logically and safely. • Verify E-Stop, brake, and general safety routines still behave as intended afte...
I need a Delta PLC & HMI specialist who can take our machining line from manual control to fully automated operation. The equipment already has sensors, drives, and safety relays in place; what’s missing is the logic and a clean operator interface. Scope • Build ladder (or structured-text) logic in WPLSoft/ISPSoft for a Delta DVP series PLC that sequences the full machining cycle—part clamping, spindle start/stop, coolant, tool change, and finished-part eject. • Design an intuitive DOPSoft HMI with run/stop controls, live status, recipe entry, alarm/acknowledge pages, and maintenance counters. • Integrate existing proximity, pressure, and temperature sensors; map all tags clearly. • Add interlocks and emergency logic that meet stan...
Simple watertreatment project Creationg of PLC and SCADA logic, including trent for analoges and pumps. complete comissioning package. IO includes, 1pump 1Lt 1Ls (LL) 1FM (Pulse)
I need a clean, well-commented ladder logic program that will run a cascading system for water-distribution pumps. The installation has two configurations—one bank of three pumps and another bank of two—and both must follow a lead-lag sequence so demand is met efficiently while equalising pump run-hours. The code must sit on a standard PLC platform (let me know the brand you prefer, I can supply the exact model once we start) and be ready to drop into my existing project. Solid rung-by-rung documentation is important because the local operators will maintain it going forward. Deliverables: • Ladder logic file for the 3-pump cascade • Ladder logic file for the 2-pump cascade • Commented I/O list and tag map • Brief commissioning guide outlining...
...Woodward Easygen 3500XT-P2 fully programmed and commissioned so it can run in parallel with an existing generator. The work centres on three core capabilities that must be proven in operation: load sharing, synchronisation, and voltage bias control. In addition, I want the set-up to expose speed bias, digital inputs and a reliable remote-start path so I can integrate the unit cleanly into the site PLC and SCADA. You will receive the current configuration file, wiring diagram and the generator’s electrical parameters. From there I expect: • A revised parameter file ready to upload to the Easygen 3500XT-P2 • Clear instructions on any required I/O terminations or jumper changes • Remote guidance during first start and paralleling test to confirm loa...
...that adjusts with high precision the opening between two knives, controlled by Omron NX102-1100 PLC via EtherCAT and EtherNet/IP. Each knife is driven by an Omron 1S servo motor (R88M-1M40030T, 400 W) with R88D-1SN04H-ECT drive and a 10:1 Apex AB060 gearbox. The system includes an HMI (Omron NB/NA) connected over EtherNet/IP for operation, monitoring, and diagnostics. The goal is to achieve and maintain two nominal openings — 400 µm and 700 µm — or a custom value defined by the operator or external PLC. The PLC must continuously calculate the current opening (difference between right and left knife positions), display it on the HMI, and send it in real time via EtherNet/IP to the main line PLC. Safety is critical: any knife motion re...
...Technology / Component | Description | | ----------------------- | ---------------------------- | ---------------------------------------------------------- | | **Field Layer** | Siemens S7-1200 PLCs | Control process logic, sensors and actuators. | | **Communication Layer** | C# Service using | Reads/writes PLC data over Ethernet (S7 TCP). | | **Data Layer** | Microsoft SQL Server 2019 + | Stores recipes, telemetry, alarms, batch history. | | **Application Layer** | C# WPF Desktop App (Phase 1) | Operator interface for control, monitoring, and reporting. | | **Optional Phase 2** | ASP.NET Core Web Dashboard | Browser-based view for supervisors (read-only). ...
I’m looking for an experienced Wecon PLC programmer to develop and commission the control logic for a manufacturing-automation line. The task includes: • Writing clean, well-structured ladder logic (or the most suitable Wecon language) that covers start-up, normal run, safety interlocks, alarms and fault recovery. • Configuring and linking the PLC with our existing HMI panels so operators can monitor status, adjust parameters and acknowledge alarms in real time. • Delivering all program files, tag lists and a concise I/O map, plus revision-controlled comments so future maintenance is straightforward. • Providing remote support during initial power-up to fine-tune timings and troubleshoot any integration issues with drives, sensors and actuator...
I need a fresh PLC program written from the ground up for a Kinco controller that will run an assembly-line setup in a manufacturing environment. Nothing exists yet, so this is a clean-slate project focused entirely on New PLC programming rather than modifying or troubleshooting code. The line is a straightforward pick-and-place assembly station with a few sensors, two stepper drives, and an air-powered indexing table. Your task is to create the complete ladder (or structured-text) logic, set up the I/O map, integrate the safety interlocks, and make sure the cycle timing is consistent with a 20-second takt time. I’m already using Kinco Builder and Kinco HMIware, so the finished project must load and run in those tools without additional licensing. I can supply a detai...
I need a Siemens-experienced PLC engineer to create a complete control solution for a set of water pumps using an S7-1500. The goal is rock-solid, fully automated pump management with clear diagnostics and easy expandability. Scope of work • Design the full control logic in TIA Portal for start/stop sequencing, pressure/flow regulation, fault handling, and energy-efficient rotation of duty pumps. • Develop accompanying HMI screens (WinCC Comfort/Advanced) that give operators intuitive status, alarms, and manual override functions. • Generate all required documentation: functional description, tag list, network diagram, and commented source code. • Simulate and bench-test the program before site deployment; deliver test reports that prove the logic under no...
I’m building a professional Live Runtime Automation Suite, an industrial software that lets factories and system integrators modify, test, and deploy PLC logic in real time without stopping production. It mirrors the live process in a shadow runtime, verifies logic changes safely, and syncs them instantly to the live PLC system. The software will include a structured text editor, real-time data sync engine, version control, and a clean, modern interface. The goal is to eliminate downtime, simplify PLC code management, and give automation teams a faster, safer way to update their control systems. Budget: $4000 USD Timeline: (6 - 8 Weeks) Please read the full documentation attached, only bid this project if you KNOW you are able to do it. Project kickoff will b...
...have a working CLICK PLC ladder program that reads three 4–20 mA analog inputs, averages each signal over 10 seconds, and then calculates a relative percentage between two of them. The math looks right on paper, yet live values are drifting about 10 % low. I suspect the issue sits in the averaging routine—possibly a formula or rung structure that’s pulling the result down. Your tasks • Pinpoint and fix the averaging logic so the displayed value aligns with the raw input (±1 %). • Trim or eliminate the 1-second timers that are currently gating the output response. I want the system to settle in roughly 2–3 seconds instead of the current 10 seconds. • Clean up any redundant rungs or tags for readability and future maintenance. &b...
I’m bringing a new physical product to life and need a cohesive team that can carry it from concept sketches all the way to production-ready files. Mechanical design sits at the heart of this project, yet the final result also relies on tight integration of electrical systems, IoT/PLC functionality, and an industrial-grade exterior finish. Here’s how I see the collaboration working: mechanical engineers shape the core mechanism and packaging, electrical specialists lay out the boards and wiring, PLC experts connect the device to the cloud, and industrial designers refine ergonomics and brand feel. Throughout, we’ll iterate quickly in CAD, exchange files in their native formats (SolidWorks, Altium, Codesys, or comparable), and meet weekly to keep all discipl...
An Automation Direct PLC on my line must receive a clean Ethernet/IP bit the instant a diner sends an order through the Square POS for Restaurants QR-code flow. Here’s the flow I need implemented: Square POS records the order → your middleware listens via Square Webhooks or another approved API method → logic translates the event into an Ethernet/IP write → the designated coil/tag in the PLC flips to “1”. When the order is completed or voided, the bit should return to “0” to keep my machine sequence in sync. Key points • PLC brand: Automation Direct (Do-more series on Ethernet/IP). • Front-end system: Square POS for Restaurants. • Comms path: native Square API or Webhooks on HTTPS, then Ethernet/IP...
I need an experienced automation professional to move my existing PLC control cabinet roughly 30 feet from its current position on the production floor. The cabinet drives an industrial automation process, so downtime must be kept to a minimum and all safety interlocks must remain intact. Key points • Environment: the new spot can get quite warm in summer but has no known dust, moisture, or other hostile conditions. • Cabling: all current field wiring and power feeds reach the new location; no additional cable runs are expected, but you’ll need to manage slack, routing, and labeling neatly. • Scope: disconnect, shift, re-mount, reconnect, and recommission the cabinet; verify every I/O channel, network drop, and safety circuit before sign-off. Provide a conc...
Project Title: Development of Object Library and Graphic Mockups for Automation Software (BMS / SCADA / HVAC) Project Description: We are seeking a UI/UX designer with experience in interfaces for automation systems, industrial control, or SCADA/BMS platforms. The goal of this project is to develop a complete library of graphical objects that will later be used in the implementation of monitoring and control software. The object library should include, but is not limited to: Buttons (normal / hover / pressed / disabled states) Dropdown menus Navigation icons (next, previous, home, main menu) Text and value display fields for live process variables Visual indicators and basic animations Gauges / tachometers / progress displays Simple trend/graph components Alarm st...
The conveyor-based book sorter I have built here in Murrieta, California is already scanning barcodes, dropping titles into the right monetization bins, and talking to a Python layer that drives most of the high-level logic. Where I am still struggling is the PLC side: intermittent faults, occasional missed hand-shakes with the Python service, and a few stubborn I/O gremlins keep the line from running lights-out. Your main mission is to hunt down and eliminate those issues so we can move confidently into full production. Although straight-up system troubleshooting is the immediate priority, I’m open to your suggestions on tighter hardware integration or small control-logic tweaks if they help us achieve rock-solid uptime. Once the sorter runs a full shift without an unplan...
...acceptance criteria for every Mechanical and HVAC asset. • Coordinate with design, construction, and controls teams to verify install readiness and resolve punch-list items early. • Lead on-site functional testing—air handlers, exhaust systems, pumps, piping loops, boilers, pressure vessels, and any supporting utilities the plant may require. • Oversee TAB and verify integration with the BMS/SCADA interface; fine-tune setpoints to achieve specified performance. • Log, track, and close issues in CxAlloy (or similar) and prepare the final commissioning report with O&M input, trend data, and a concise executive summary for stakeholders. • Train maintenance staff and hand over a fully documented system, ready for reliable, efficient operat...
.../ encapsulation details for reliable outdoor use (targeting at least IP65 performance). • Production-ready documentation: schematics and PCB layout (Altium or KiCad), mechanical drawings, full BOM with sourcing notes, and fabrication files. • Embedded readout electronics and firmware (Arduino, STM32 or similar) capable of logging high-resolution capacitance changes the analogue input card in plc for site-wide collection. • Calibration procedure and sample code to convert raw capacitance into yield-stress values, validated with a small concrete test rig. • One fully assembled prototype plus photos/videos of bench and in-situ tests confirming stable operation for a minimum of four weeks. I’ll handle large-scale field trials once the prototype is ...
-Migrate PLC program AB CompactLogix to Siemens 1500 -Migrate HMI Panelview Plus 10" to Siemens Unified Comfort 10"
...whole system rewired around a modern PLC/timer so the process timing is rock-solid and adjustable from a panel. Scope Filling Machine • Remove the existing timer circuitry and install a PLC-based control panel and timer. • Design and supply the new wiring diagram, cabinet layout, and bill of materials. • Program the timer to manage only the filling-process timing for now; liquid-level or motor control can stay on the old relays but please leave spare I/O for future expansion. • Calibrate the cycle time on site (or guide me remotely) until the dose is repeatable within my ±1 % tolerance. • location in King Abdullah Economic City (KAEC) near Rabigh in Saudi Arabia. Scope Cooking Machine • Remove the existing timer ci...
We have 5 ongoing Control Engineering projects for work support. We’re looking for engineers with hands-on experience in industrial automation, PLC programming (Allen-Bradley, Siemens, Fanuc), and HMI/SCADA systems like Ignition, Wonderware, FactoryTalk, or Aveva Edge. The work involves system design, programming, testing, and commissioning across multiple automation domains including manufacturing, material handling, and power monitoring (EPMS). Knowledge of Ethernet/IP, Modbus, robotics integration, and Python scripting will be an added advantage.
I have a Click PLC handling up to 12 DC servo motors over RS-485 and a 4D Systems touchscreen for the user interface. I need a fresh ladder-logic program plus the HMI project so the entire package works seamlessly together. HMI scope The touchscreen will have four pages. Each page must include both manual controls for individual motors and an automated sequence option. Start/Stop commands, step-count entry, and on-screen calibration of the step value are required. Two of the motors will also be able to run directly from a hard-wired push-button, bypassing the screen when will also need adjustable headings for recipes of the different vale’s in steps of each motor steps and volumes PLC logic requirements • Address and command as many as 12 DC servos on the R...
...control-system concept for industrial automation from idea to tested prototype. The work spans schematic capture, PCB layout, component selection, firmware or embedded software development, and validation on real-world loads. Because this project sits inside an active production environment, I’m after someone who already has demonstrable experience with similar industrial-grade controllers—think PLC-style I/O, robust power regulation, fail-safe circuitry, EMI/EMC-aware board layout, and protocol stacks such as Modbus, CAN, or Ethernet/IP. If you can show previous projects where you delivered a working board plus firmware that met industrial safety or reliability standards, you’re exactly who I’m looking for. Core deliverables will include: • C...
I need a Siemens-experienced PLC engineer to create a complete control solution for a set of water pumps using an S7-1500. The goal is rock-solid, fully automated pump management with clear diagnostics and easy expandability. Scope of work • Design the full control logic in TIA Portal for start/stop sequencing, pressure/flow regulation, fault handling, and energy-efficient rotation of duty pumps. • Develop accompanying HMI screens (WinCC Comfort/Advanced) that give operators intuitive status, alarms, and manual override functions. • Generate all required documentation: functional description, tag list, network diagram, and commented source code. • Simulate and bench-test the program before site deployment; deliver test reports that prove the logic under no...
I need a Siemens-experienced PLC engineer to create a complete control solution for a set of water pumps using an S7-1500. The goal is rock-solid, fully automated pump management with clear diagnostics and easy expandability. Scope of work • Design the full control logic in TIA Portal for start/stop sequencing, pressure/flow regulation, fault handling, and energy-efficient rotation of duty pumps. • Develop accompanying HMI screens (WinCC Comfort/Advanced) that give operators intuitive status, alarms, and manual override functions. • Generate all required documentation: functional description, tag list, network diagram, and commented source code. • Simulate and bench-test the program before site deployment; deliver test reports that prove the logic under no...
...Scale should handle 50 - 750 kg. The scale will use a platform to measure the weight with four load cells under it, and the signals from the load cells will be sent to the controller via a junction box. The controller will send that data to the PLC using either RS-232 or RS-485 port. The PLC will display the current weight on the UI screen. And PLC can control the filler machine with three signal types: filling valve full open, filling valve 30% open, filling valve shut off, depending on the weight being read on the scale at that moment. Also, the PLC has been able to communicate in both directions with the controller and the screen to set zero/tare, set the target weight, and run weight calibrations. System Components Scale platform(1.5 m × 1.5 m) ...
...yet still accessible to a non-engineer who already knows basic energy terms. After the technical walk-through, I want concise sections on cash-flow analysis, financing structures, and long-term savings so the audience sees how the numbers connect to the hardware. Here’s the flow I have in mind: start with a schematic animation that shows irradiation, PV array output, inverters, combiner boxes, SCADA, and grid tie-in. Layer in typical performance ratios and efficiency losses as the narration progresses. Follow that with a segment on CapEx vs. OpEx, a sample CFA spreadsheet visual, then financing options such as PPAs or lease models, closing with a savings timeline. Please handle: • Scriptwriting (English) • Voice-over and royalty-free background track &bull...
I need a console application to read data register values from a Panasonic PLC via RS232C and send that data to a PC. Requirements: - Use C++ - Use the SerialPort Library for RS232C communication - Console application Ideal Skills: - Proficiency in C++ - Experience with SerialPort Library - Familiarity with RS232C communication protocols - Background in PLCs, especially Panasonic
I have an existing PLC program built in Codesys and I now need a simple HMI layer added on top of it. The goal is limited in scope—just enough to let an operator: • View real-time data from key tags • Trigger essential control buttons (start, stop, reset, etc.) • Receive basic alarm notifications with clear text You can reuse standard Codesys visualization elements or any lightweight HMI framework that runs natively inside Codesys; the simpler the better as long as it’s reliable. A clean, single-screen layout is fine—I’m not looking for extensive graphics or multi-page navigation. Deliverable: a Codesys project file (or visualization package) dropped back into my existing application, clearly commented so I can map variables and tweak ...
...part of our thesis project titled “Development of Training Modules for Fresh Engineers Using Industrial Simulation.” The Factory I/O part covers the 3D visual process simulation, and now we need to develop the CODESYS simulation part that demonstrates PLC programming logic for the same training modules. Objective To create a fully functional CODESYS simulation (no real hardware) that replicates common beginner automation mistakes and their correct solutions. The simulation will help demonstrate how trainees can identify, troubleshoot, and fix PLC-related issues using virtual controllers. Develop simulation projects in CODESYS V3.x (preferably v3.5 or higher). Use CODESYS Control Win (SoftPLC) for offline simulation (no hardware). Create ladder logic or FB...
...Multibody .xml export for a full shaft-to-car layout (-1, 0, 1 … 10). • Simscape / Simulink setup: Drop in basic actuators and position/door sensors, wire them into a Simulink model, and implement a priority-based dispatch algorithm so both cars move independently without collisions. • OPC-UA link: Expose key tags (calls, car position, door status) via OPC-UA and prove connectivity to a B&R X90 PLC in Automation Studio. A minimal HMI page that shows floor position and door state is enough at this stage. • Documentation & demo: – STEP file, .sldasm/.sldprt sources, and Simulink model – Node list and sample Automation Studio project – Short test report, screenshots, and a quick run-through video I’m after a le...
I have a running Allen-Bradley RSLogix 5000 application—PLC logic and accompanying HMI screens—that controls a process plant. We’re retiring the AB hardware and need the entire solution rebuilt in Siemens TIA Portal for a new TIA Portal Controller. Speed is critical; I’d like an engineer who can jump in immediately and keep the migration smooth. Scope • Re-create the PLC logic in TIA Portal, preserving tag names, comments, and step sequence behaviour. • Translate all existing HMI graphics, alarms, and faceplates to Siemens WinCC inside TIA. • Maintain identical process-control functionality, interlocks, PID tuning parameters, and fault handling. • Provide an offline simulation or test project so I can review before site dep...
I need a solid Siemens-based PLC program that keeps an entire food-manufacturing line running smoothly. The key requirement is precise conveyor-belt speed control for every section of the line, including coordinated starts, stops and line-balancing logic. Here’s what I’m after: • Develop ladder or structured-text code in TIA Portal for a Siemens CPU (S7-1200/1500 class) covering motor starters, VFD interfaces and safety circuits. • Integrate existing sensors, photo-eyes and encoders so each conveyor section can self-regulate speed and detect jams or product gaps. • Add operator-friendly HMI screens (WinCC) that display speeds, alarms and manual override functions. • Deliver well-commented source files, an I/O list, and a brief commissioning...
Our plant runs a continuous wet-to-dry production line that combines wet milling, a decanter centrifuge, a fluidized bed dryer, dry milling and pneumatic transfer into bulk storage. I grant secure remote access to the SCADA/PLC interface and rely on you to act as an extra set of eyes during each shift. Your main focus is guiding the on-site operators in real time: confirming critical steps, walking them through alarms and proposing fine-tuned setting changes before issues escalate. Hands-on familiarity with a decanter centrifuge is essential, as that stage dictates the moisture profile for every downstream unit. Comfortable navigation of typical control platforms, alarm hierarchies and trend charts is expected so that advice comes quickly and in language the floor team und...
...Presales Team Leader • Optional tagline: Bridging Technology, Innovation, and Urban Intelligence • Background: Subtle smart city visuals, blue/gray palette. Design Note: Modern typography, glowing city overlay, and minimalist layout. ________________________________________ 2. Areas of Experience – Technological Solutions Purpose: Highlight solution expertise. Content: • Smart Cities • IoT & IIoT • SCADA, PLC, RTU, and Instrumentation • Telemetry • XR/AR/VR Applications • Digital Twin Design Note: Use technological icons with concise labels, organized in a hexagonal or connected-node design. ________________________________________ 3. Areas of Experience – Sectors Purpose: Showcase the vertical industries served. Con...
4 Weeks timeline. Milestone 1 -> Advanced payment on Quote Acceptance 6800 INR Milestone 2 -> 21,200 INR Week 1 Schematic Population in Altium from Oct 20th to Oct 27th. Milestone 3 -> 20,000 INR Week 2 PCB Design and Layout in Altium from 28th Oct to Nov 11th. Milestone 4 -> 20,0000 INR Finalization and feedback review, Project cleanup, and file delivery. Nov 13th to Nov 20th. I will not be available on Saturdays and Sundays. Also will not be available on the 3rd of Nov. Project deliverables: Full packaged Altium project files, component libraries and Model Libraries. Manufacturing files, Bill of Materials, Pick and place files, and Gerber files. All components from Mouser and/or Digikey.
4 Weeks timeline. Milestone 1 -> Advanced payment on Quote Acceptance 6800 INR Milestone 2 -> 21,200 INR Week 1 Schematic Population in Altium from Oct 16th to Oct 22nd. Milestone 3 -> 20,000 INR Week 2 PCB Design and Layout in Altium from 23rd Oct to Nov 5th. Milestone 4 -> 20,0000 INR Finalization and feedback review, Project cleanup, and file delivery. Nov 5th to Nov 15th. I will not be available on Saturdays and Sundays. Also will not be available on the 3rd of Nov. Project deliverables: Full packaged Altium project files, component libraries and Model Libraries. Manufacturing files, Bill of Materials, Pick and place files, and Gerber files. All components from Mouser and/or Digikey.
Cavisa Oil Lda is upgrading its Seahawk cementing unit so every sack pumped, part replaced, and pressure test performed is captured automatically instead of on paper. What I need is a combined data-management and inventory-tracking system that plugs into the unit’s existing sensors and PLC signals, stores the raw readings securely, and turns them into useful information on a live dashboard. The dashboard should refresh in real time, giving operations staff instant visibility of: • Daily operation logs (volumes, rates, pressures, temperatures) • Cement-usage reports (blend, density, total sacks, leftovers) • Equipment-replacement records (part number, reason for change, time stamp) I expect clean database architecture, user-friendly web or tablet interfa...
...delivery controllers - **Check Point**: Security gateways #### 7. Web Applications - **Administrative Portals**: Web-based admin interfaces - **API Endpoints**: RESTful APIs requiring privileged access - **Legacy Web Apps**: Older web applications - **SaaS Platforms**: Third-party SaaS admin panels #### 8. Specialized Systems - **Mainframes**: IBM z/OS, AS/400 systems - **Industrial Control**: SCADA, PLC systems - **Security Appliances**: SIEM systems, vulnerability scanners - **Backup Systems**: Enterprise backup solutions - **Monitoring Tools**: Network monitoring, APM tools ## Enhanced Configuration Schema ### Core Foundation 1. **Project Setup** - Create .NET 8 WPF application - Set up project structure - Configure dependency injection - Basic logging f...
The goal is to build brand-new automation software in C# that talks directly to our PLC hardware and drives a manufacturing assembly line from start to finish. I already have the electrical side covered; what I need is the Windows-based control layer that will issue start/stop commands, read sensor feedback, and coordinate each station so the line keeps its rhythm without manual intervention. The PLCs are standard industrial units (Siemens and Allen-Bradley are typical on our floor), so the program will have to exchange data over the usual protocols—OPC UA or Modbus/TCP are fine as long as the response times are tight enough for real-time control. A simple, operator-friendly GUI is essential: big status indicators, manual jog buttons, and basic fault alarms. Live production c...
...engineer—or a tight-knit duo—who can cover BOTH mechanical design and PLC/automation. What I need Mechanical • Model the platen, frame, tie-bar layout and QMC locking mechanism in SolidWorks or Creo (I work with both, so fluency in both is essential). • Size actuators, guides and piping paths, then create a basic BOM and exploded views that explain the QMC sequence. Automation • Lay out the PLC architecture to run steam, vacuum, cooling and ejection cycles. • Produce an I/O list, timing diagram and a ladder/FBD logic outline ready for bench testing. Core deliverables 1. Parametric 3D assembly and detail drawings for all main sub-systems. 2. Animation or step file that demonstrates the quick change sequence. 3. PLC program ...
I'm seeking an experienced Allen-Bradley PLC programmer for support on various ongoing jobs. Key Tasks: - Programming - Debugging - Troubleshooting We will be working on development, retrofitting, and improving control methods. The ideal freelancer should have: - In-depth knowledge of Allen-Bradley PLC systems - Proven experience in programming, debugging, and troubleshooting - Strong problem-solving skills - Ability to work on both new developments and existing setups with issues Please provide examples of similar work done and your approach to handling complex PLC tasks.
